Impact of industrial waste fillers in self-compacting mortars: A comparative analysis of mechanical performance
Rattachement africain : Algérie. Niveau de preuve : code pays fourni par la source.
Le résumé fourni par la source
This study investigates the viability of utilizing non-biodegradable industrial waste streams specifically ground glass, crushed brick, and sanitary ceramics as alternative fillers in self-compacting mortars (SCMs). A conventional SCM mixture incorporating traditional limestone filler served as the control benchmark. The research assessed the influence of substituting conventional fillers with waste- derived materials, varying their proportions while maintaining a constant cement content. The experimental results showed that the inclusion of alternative fillers enabled the target slump flow values to be achieved with a lower water-cement ratio, thus reducing water demand. However, the mortars with brick and ceramic fillers had longer mini-V- funnel flow times. Analysis of the hydration heat revealed that brick and ceramic fillers accelerated early hydration reactions, whereas glass fillers exhibited a delayed reactivity. Mortars containing these alternative fillers showed significant mechanical strength increases over time; compressive strength and dynamic modulus of elasticity increased significantly. After 365 days of curing, compressive strength values increased by 34% and 37% for mortars containing brick and ceramic fillers, respectively, and by 31% for those incorporating glass fillers, relative to the control mortar. These findings highlight the promising potential of valorizing industrial waste materials as efficient, economical, and environmentally sustainable alternatives to conventional limestone fillers in SCMs.
Ce résumé expose les affirmations des auteurs. BNTIC ne l’interprète pas comme une validation indépendante des résultats.
Le contrôle bibliographique ouvert
DOI retrouvé dans Crossref DOI retrouvé ; titre concordant.
- Titre Crossref
- Impact of industrial waste fillers in self-compacting mortars: A comparative analysis of mechanical performance
- Date Crossref
- 01/01/2025
- Éditeur
- MIM Research Group
- Type
- journal-article
Ce recoupement confirme des métadonnées liées au DOI. Il ne confirme ni la méthode ni les conclusions de l’étude, et il ne compte pas comme une seconde source scientifique indépendante.
Où se fait cette recherche
-
Polytechnic School of Algiers Polytechnic School of Algiers, Algérie (code pays fourni par la source)Université ou école supérieure
-
University of Algiers 3 University of Algiers, Algérie (code pays fourni par la source)Université ou école supérieure
-
Université Mustapha Stambouli de Mascara Algérie (code pays fourni par la source)Université ou école supérieure
-
École Supérieure en Sciences Appliquées de Tlemcen Tlemcen, Algérie (code pays fourni par la source)Université ou école supérieure
-
University of Tamanghasset Algérie (code pays fourni par la source)Université ou école supérieure
-
University of Algiers 1 Department of Architecture University of Algiers, Algérie (pays nommé en fin d’affiliation)Université ou école supérieure
-
National Polytechnic School of Oran Department of Civil Engineering National Polytechnic School of Oran, Algérie (pays nommé en fin d’affiliation)Université ou école supérieure
-
University of Mascara Department of Civil Engineering Algérie (pays nommé en fin d’affiliation)Université ou école supérieure
-
Faculty of Sciences and Technology Algérie (pays nommé en fin d’affiliation)Université ou école supérieure
Polytechnic School of Algiers (Polytechnic School of Algiers, Algérie), University of Algiers 3 (University of Algiers, Algérie) et Université Mustapha Stambouli de Mascara (Algérie), avec 6 autres affiliations. Pays d’affiliation : Algérie.
Une affiliation ne permet pas de déduire la nationalité d’un auteur.