Aller au contenu principal
Accès ouvert déclaré 2024 article

Effect of Dehydrogenation and Heat Treatments on the Microstructure and Tribological Behavior of Electroless Ni-P Nanocomposite Coatings

4Citations signalées, ce qui n’est pas une note de qualité
3Institutions déclarées
1Pays d’affiliation déclarés

Rattachement africain : it. Niveau de preuve : code pays fourni par la source.

Le résumé fourni par la source

High phosphorus Ni-P coatings, both unreinforced and modified by the addition of alumina (Al2O3) and zirconia (ZrO2) nanoparticles, were manufactured by electroless deposition technique and heat-treated with different temperature and duration schedules. The effect of dehydrogenation (200 °C for 2 h) and its combination with crystallization heat treatment was studied in terms of microstructural changes and wear resistance. The amorphous structure of the coatings was not altered by the introduction of both Al2O3 and ZrO2 nanoparticles, and the addition of 1.5 g/L of ZrO2 yielded the highest microhardness due to better particles dispersion. Dehydrogenation improved hardness because of the early stages of grain growth; however, the greatest improvement in hardness (+120% compared to unreinforced Ni-P) was obtained after annealing at 400 °C for 1 h, because of the microprecipitation of the Ni3P crystalline phase induced by thermal treatment. No detectable differences in hardness and microstructure were detected when annealing at 400 °C for 1 h with or without prior dehydrogenation; however, the dehydrogenated coatings exhibited a lower Young’s modulus. ZrO2-reinforced coatings demonstrated improved wear resistance, and wear tests revealed that dehydrogenation is fundamental for lowering the coefficient of friction (−14%) and wear rate (−97%) when performed before annealing at 400 °C for 1 h. The analysis of the wear tracks showed that the non-dehydrogenated samples failed by complete coating delamination from the substrate, with abrasion identified as the predominant wear mechanism. Conversely, the dehydrogenated samples demonstrated better resistance due to the formation of a protective oxide layer, leading to an overall increase in the coating wear resistance.

Ce résumé expose les affirmations des auteurs. BNTIC ne l’interprète pas comme une validation indépendante des résultats.

Le contrôle bibliographique ouvert

DOI retrouvé dans Crossref DOI retrouvé ; titre concordant.

Titre Crossref
Effect of Dehydrogenation and Heat Treatments on the Microstructure and Tribological Behavior of Electroless Ni-P Nanocomposite Coatings
Date Crossref
20/11/2024
Éditeur
MDPI AG
Type
journal-article

Ce recoupement confirme des métadonnées liées au DOI. Il ne confirme ni la méthode ni les conclusions de l’étude, et il ne compte pas comme une seconde source scientifique indépendante.

Où se fait cette recherche

  • National Interuniversity Consortium of Materials Science and Technology pays non établi dans la notice
    Université ou école supérieure
  • Sapienza University of Rome INSTM Reference Laboratory for Engineering of Surface Treatments via Eudossiana 18 pays non établi dans la notice
    Université ou école supérieure
  • University of Ferrara Department of Engineering (DE) pays non établi dans la notice
    Université ou école supérieure

National Interuniversity Consortium of Materials Science and Technology, INSTM Reference Laboratory for Engineering of Surface Treatments via Eudossiana 18 — Sapienza University of Rome et Department of Engineering (DE) — University of Ferrara.

Une affiliation ne permet pas de déduire la nationalité d’un auteur.

Les sujets associés

Electrodeposition and Electroless CoatingsMetal and Thin Film MechanicsSemiconductor materials and interfaces

BNTIC News n’est pas le producteur de ces données. Les publications sont interrogées à la demande dans Crossref, OpenAIRE, DOAJ, Europe PMC, HAL, DataCite, AfricArXiv, ROR et la Banque mondiale, sans clé d’accès. OpenAlex reste optionnel. Aucun service payant n’est nécessaire et aucune donnée externe n’est enregistrée en base. Consulter les sources et leurs limites.